method of reducing industrial natural gas boiler exhaust gas temperature

Reduction of CO2 Productionin Industry by Using

2015-3-7 · The operating data for Boiler No.1 are shown in Table 1. As seen in the table,since the fuel is natural gas (NG), the exhaust consist of less than 2 ppm SOX. With this assumption, the dew point for sulfuric acid in the exhaust gas is between 70 to 100 °C. Thus, to

Get a Quote

Industrial Process Heating - Technology Assessment

2015-2-13 · 30 such as natural gas, coal, biomass and fuel oils. In 2010, process heating consumed approximately 330 76 in lower temperature industrial process heating (lt;400 deg. F.). Use of steam based systems is largely for 159 reducing energy use and reducing Green House Gas (GHG) emissions to meet the national goals. Process Figure 2 - Major

Get a Quote

Boiler Combustion | CleanBoiler.org

Flue gas recirculation, or FGR, is the most effective method of reducing NOx emission from industrial boilers with inputs below 100 MMBtu/hr. FGR entails recirculating a portion of relatively cool exhaust gases back into the combustion process in order to lower the flame temperature

Get a Quote

Commercial Buildings - NW Natural

Commercial Buildings View thorough guidelines on reducing energy consumption in commercial buildings and kitchens. Proper operation and maintenance of gas fired systems can save a significant amount of natural gas. Here are some ideas for reducing energy consumption in your gas fired systems through proper operating and maintenance procedures.

Get a Quote

10 Best Boilers of 2020: Gas, Propane, Oil, Electric

The Slant/Fin Sentry boiler is a gas hot water boiler with an efficiency of 84.4% AFUE. The Sentry comes with several noteworthy features such a pre-purge option to conserve heat, a LED display which monitors system water temperature and allows the user to control the temperature as well, and a specially-designed insulated jacket to prevent heat loss and reduce operating noise.

Get a Quote

Energy Conservation Opportunities in an Industrial

In this study, an experimental study has been performed for a natural gas fueled boiler operating at 42,000-kPa pressure and 713.15-K temperature with a nominal capacity of 33.33 kg/s to find

Get a Quote

How To Prevent Freezing In Gas Pressure Reducing

The potential for freezing can be identified by calculating the temperature drop and subtracting from the initial temperature. For example, if a pressure reducing regulator dropped the pressure of a gas line from 500 psi to 350 psi (34 to 24 bar) and the initial temperature is 50°F (10°C), the final temperature

Get a Quote

NOx Reduction: Flue Gas Recirculation vs Selective

2018-8-5 · Natural Gas (NG) • 26.0 g/GJ (50 ppm reduces combustion temperature thus reducing thermal NOx. Using conventional burner technology, reductions of up to 80% are possible. Using a 100 MMBTU/hr natural gas register burner as a • Ammonia injected at boiler flue gas outlet

Get a Quote

INDUSTRIAL NATURAL GAS ENERGY EFFICIENCY

2014-8-13 · natural gas energy savings opportunities in the areas of process heating and steam generation. These areas use about 85 percent of industrial natural gas and represent major opportunities to reduce natural gas use in California industries. The no‐cost tools can be downloaded at:

Get a Quote

Quantifying Savings From Improved Boiler Operation

2010-9-22 · Exhaust gas temperature, Tex, and excess air, EA, can be measured using a combustion analyzer. For example, consider a natural gas boiler using 50% excess combustion air at 70 F and exhausting combustion gasses at 400 F. The results from this method are

Get a Quote

BOILER EFFICIENCY GUIDE - Cleaver-Brooks

2018-8-5 · The stack temperature of a 4-pass boiler will be lower than the stack temperature of a 2 or 3-pass boiler, of the same basic design, operating under similar add-on devices if the boiler is designed for optimum flue gas velocities in the first place. Each boiler pass should be designed with a

Get a Quote

Method for converting urea to ammonia - Noell, Inc.

1994-1-25 · A method is provided for reducing NOx in a combustion exhaust gas stream from a boiler. The method includes the steps of converting an aqueous solution of urea to ammonia by heating the urea solution to a temperature of 350°-650° F. in an injection lance system.

Get a Quote

Combustion Booklet 2013 (2013,

13 - Flue Gas Recirculation – Flue Gas Recirculation, FGR, is a method of NOx reduction that lowers the temperature of the flame, and therefore reduces thermal NOx. A portion of the exhaust gas is re-circulated into the combustion process, cooling the area.

Get a Quote

Combustion Analysis Basics - ICDST

2019-4-16 · measurement of flue gas concentrations and gas temperature, and may include the measurement of draft pressure and soot level. To measure gas concentration, a probe is inserted into the exhaust flue and a gas sample drawn out. Ex-haust gas temperature is measured using a thermocouple positioned to measure the highest exhaust gas temperature.

Get a Quote

South Coast Air Quality Management District

2017-9-14 · a) This protocol is for B/PHs fired on natural gas only. b) This protocol may be used for the following types of efficiency improvements on a natural gas-fired B/PH: 1) Addition of a combustion air preheater, economizer or other system that reduces the flue gas exhaust temperature and increases the B/PH thermal efficiency.

Get a Quote

1.4 Natural Gas Combustion - US EPA

2015-9-10 · average gross heating value of natural gas is approximately 1020 British thermal units per standard cubic foot (Btu/scf), usually varying from 950 to 1050 Btu/scf. 1.4.2 Firing Practices3-5 There are three major types of boilers used for natural gas combustion in the industrial, commercial, and utility sectors: watertube, firetube, and cast iron.

Get a Quote

Low-NOx Burners for Industrial Boilers | HPAC

FGR is the process by which exhaust gas is introduced into the combustion-air stream prior to a burner. Flue gas also is relatively cool (300°F to 550°F, depending on the design of the boiler and whether there is a feedwater economizer) with respect to flame temperature, and flue gas has little oxygen from the combustion process.

Get a Quote

Combustion Analysis Basics - ICDST

2019-4-16 · measurement of flue gas concentrations and gas temperature, and may include the measurement of draft pressure and soot level. To measure gas concentration, a probe is inserted into the exhaust flue and a gas sample drawn out. Ex-haust gas temperature is measured using a thermocouple positioned to measure the highest exhaust gas temperature.

Get a Quote

How To Prevent Freezing In Gas Pressure Reducing

The potential for freezing can be identified by calculating the temperature drop and subtracting from the initial temperature. For example, if a pressure reducing regulator dropped the pressure of a gas line from 500 psi to 350 psi (34 to 24 bar) and the initial temperature is 50°F (10°C), the final temperature

Get a Quote

KEY COMPONENTS OF BOILERS | Boilers Guide

The boiler is the part of the system that heats the water to be distributed. The key elements of a boiler include the burner, combustion chamber, heat exchanger, exhaust stack, and controls. Boiler accessories including the flue gas economizer are also commonly used as an effective method to recover heat from a boiler. Key Components of Boilers

Get a Quote

method of reducing industrial natural gas boiler exhaust gas temperature